Search:

Type: Posts; User: SLO015

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    10
    Views
    41,694

    Huge thread bump for whoever visits this forum...

    Huge thread bump for whoever visits this forum any more, but the issue in the end was the aftermarket dizzy. I purchased a second-hand unit from the wrecker and replaced the inner seal, bearing and...
  2. Replies
    20
    Views
    16,470

    Problem solved! So since my last post I did a...

    Problem solved! So since my last post I did a compression test, which gave results of around 165 psi across all four cylinders. I also tested the fuel pump resistance which was within spec. I noticed...
  3. Replies
    21
    Views
    42,579

    Frustrating

    Frustrating
  4. Replies
    20
    Views
    16,470

    Yesterday I blocked off the EGR system, which...

    Yesterday I blocked off the EGR system, which unfortunately has failed to address the hesitation issue. The BPT valve was blocked up with carbon when I took it off so that would have no doubt been...
  5. Replies
    20
    Views
    16,470

    Hmm fair enough! I'll see how I go in trying to...

    Hmm fair enough! I'll see how I go in trying to acquire a fuel pressure test kit then.
  6. Replies
    20
    Views
    16,470

    Speaking from experience, haha? Any idea as to...

    Speaking from experience, haha? Any idea as to how much fuel would be expected to come out whilst priming the fuel pump, assuming the pump is working as it should?
  7. Replies
    20
    Views
    16,470

    I'll be sure to check that too. I don't have a...

    I'll be sure to check that too. I don't have a fuel pressure gauge but I guess I could always disconnect the fuel feed line at the filter and put it in a jar to see whether there's any issues with...
  8. Replies
    20
    Views
    16,470

    No worries! Good to know that they're a viable...

    No worries! Good to know that they're a viable option.
  9. Replies
    20
    Views
    16,470

    Thanks for the reminder about the fuel pump mate!...

    Thanks for the reminder about the fuel pump mate! It is something I need to put a multimeter on and check. I can guarantee it'd be the original one though, and like you said, the strainer is likely...
  10. Replies
    20
    Views
    16,470

    It's been about 15,000k's max since I replaced...

    It's been about 15,000k's max since I replaced the fuel filter. Was either last service or the one before, can't quite remember but it has definitely been done recently
  11. Replies
    20
    Views
    16,470

    That's something that's definitely on the list to...

    That's something that's definitely on the list to do as well. I have done it before (with the same stuff) but it can't hurt to put another can or two through.

    As for the k's, it's just gone over...
  12. Replies
    20
    Views
    16,470

    It's definitely as per the video, with the...

    It's definitely as per the video, with the 'square edge' of the plug facing to the right.

    Yeah that's exactly what was happening. When it was connected it was saying 'could not connect'. I'm not...
  13. Replies
    20
    Views
    16,470

    Hey mate, I watched that video the other day,...

    Hey mate, I watched that video the other day, that's the procedure I have been attempting to do to no avail. I switch the key to the on position, the check engine light comes on and stays on, I...
  14. Replies
    20
    Views
    16,470

    Issue with checking fault codes

    I'm wondering whether someone has experienced the same issue I have and can provide some advice on how to sort it out. I have a series 2 N15 sedan (GA16), and I'm trying to retrieve the fault codes...
  15. Replies
    10
    Views
    41,694

    Sorry to bump this thread again, but I'm once...

    Sorry to bump this thread again, but I'm once again having the same issue . It is much harder to replicate this time around which is odd, but from 1k rpm up to about 1,500 there is just a huge flat...
  16. Replies
    10
    Views
    41,694

    Figured I'd make a bit of a post on this process...

    Figured I'd make a bit of a post on this process regardless; it may just help someone in the future!

    Anyways; the photo below shows the gasket kit that I was supplied (by Repco). This was ordered...
  17. Replies
    10
    Views
    41,694

    The dizzy was actually quite cheap haha. I think...

    The dizzy was actually quite cheap haha. I think it was $150 or something like that?

    I've solved the problem by the way... long post ahead. So I pulled the spark plugs this morning to have a...
  18. Replies
    10
    Views
    41,694

    I have a feeling it is mate.. there most...

    I have a feeling it is mate.. there most definitely isn't a 5th lead from the dizzy to the coil. On my dizzy, there are only four leads from the dizzy to the engine and that's it. I'm going to clean...
  19. Replies
    10
    Views
    41,694

    Yeah mate, it has occurred again today and taking...

    Yeah mate, it has occurred again today and taking note of the rpm at which it happened it was more around 1,500 rpm. This was once again taking off in first and shifting from first to second or...
  20. Replies
    10
    Views
    41,694

    Following on from this, I have done a bit of...

    Following on from this, I have done a bit of research online with people have similar problems, and a lot of the suggestions said look at the air flow meter. I pulled the plug off of the air flow...
  21. Replies
    10
    Views
    41,694

    Hesitation on take off/changing gears

    Hey everyone,

    I've just noticed an issue where my N15 seems to hesitate for a second or so and then begin to build up speed/revs when taking off and also when shifting ie. from first to second or...
  22. Replies
    1
    Views
    5,497

    Wanted Managed to find some, cheers anyway!

    Managed to find some, cheers anyway!
  23. Replies
    7
    Views
    6,840

    I've replaced both of the hoses from the power...

    I've replaced both of the hoses from the power steering reservoir. I ripped the old ones off and got replacement lengths from Enzed... was cheap and fairly easy to do. The one that goes to the back...
  24. Replies
    1
    Views
    5,497

    Wanted N15 roof racks - Adelaide, SA 5000

    For Sale/Wanted/Wrecking wanted_parts
    Brief Description N15 roof racks
    Condition Good
    City/Town Adelaide
    State SA
    Postcode 5000
    Contact Details PM
    Price 100
    Details I'm...
  25. Replies
    2
    Views
    3,101

    I have a Clutchpro one in mine with a new genuine...

    I have a Clutchpro one in mine with a new genuine rear main seal. 6 months on, no dramas so far!
Results 1 to 25 of 59
Page 1 of 3 1 2 3