Search:

Type: Posts; User: sss4me

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    152

    some guys use n16 hubs in their n15 to put...

    some guys use n16 hubs in their n15 to put skyline brakes on. this moves the hubs out about 1cm each side. dunno about the control arms though, or even if they fit.
  2. Replies
    11
    Views
    952

    it does, but there's not much to them at all....

    it does, but there's not much to them at all. probs be structural damage
  3. Replies
    11
    Views
    952

    lower control arms bent. tie rods bent.strut tops...

    lower control arms bent. tie rods bent.strut tops busted. limp it to a suspension shop for a look see.
  4. Replies
    12
    Views
    27,794

    The angles used on the valve grind are determined...

    The angles used on the valve grind are determined by the lift of the cam to be used & the required rpm range & capacity of the engine. That being said the VE heads lend themsleves to higher rpm...
  5. Replies
    2
    Views
    597

    Its more the torque, and how you treat it, but...

    Its more the torque, and how you treat it, but 160kw you should be ok. my ve's nearly there, and its been trouble free for 4 years. you should get a lsd diff (mfactory/quaife/ s/h nismo) otherwise...
  6. Replies
    4
    Views
    739

    not 100% on n14, but there is a fix to program a...

    not 100% on n14, but there is a fix to program a remote on n15. http://pulsar.org.au/forums/showthread.php?115-How-to-Program-a-factory-remote-N15-amp-N16&highlight=program+remote
  7. Replies
    4
    Views
    631

    yes, though the temp sensor may be an issue. ...

    yes, though the temp sensor may be an issue.

    http://www.autotechmotoring.com/product/autotech-motoring-parts/18-bspt-oil-pressure-sensor-adapter-dual-18-npt
  8. Replies
    4
    Views
    631

    not easy without a remote oil filter block or a...

    not easy without a remote oil filter block or a sr20ve oil filter block with a sandwich plate, mainly due to the long temp sensor.
  9. Replies
    3
    Views
    734

    got my 26mm one from natrad. not as cheap as ebay...

    got my 26mm one from natrad. not as cheap as ebay etc, but maybe a bit better quality.
  10. Replies
    2
    Views
    606

    he is on f/b. i chat with him often. you use...

    he is on f/b. i chat with him often. you use that? he is on the pga and pog.
  11. Replies
    2
    Views
    965

    probably not enough change with a cammed de to...

    probably not enough change with a cammed de to warrant 4-1's. worth doing with the higher redline of a ve though. fuji's are a good option if the coin permits on a de.
  12. Replies
    3
    Views
    1,047

    basically you need your choice of caliper,...

    basically you need your choice of caliper, matching rotors milled down a TOTAL of 8mm off the diameter, then redrilled to 4x100, same as the studs will need to be. n16 hubs to fit the calipers too...
  13. Replies
    3
    Views
    905

    bottle top and sealant

    bottle top and sealant
  14. Replies
    3
    Views
    905

    air baffle designed to reduce intake noise. bin...

    air baffle designed to reduce intake noise. bin it.
  15. Replies
    4
    Views
    1,043

    yes. but change your old temp sensor and dizzy...

    yes. but change your old temp sensor and dizzy into the new motor. temp sensor has a different plug. n15 dizzy has internal coil, n14 doesnt. good time to clean out the iacv as well
  16. Replies
    4
    Views
    1,043

    yes. you will need the old n15...

    yes. you will need the old n15 flywheel/clutch/flywheel bolts, temp sensor, dizzy,ecu, and wiring.
  17. Thread: Spark Plugs

    by sss4me
    Replies
    3
    Views
    1,391

    unless you got some serious mods (like 12-1+...

    unless you got some serious mods (like 12-1+ pistons), your current plug is fine.
  18. Thread: Fuel Additive

    by sss4me
    Replies
    6
    Views
    1,955

    yes, that will do. 1/4 remove the aicv hose from...

    yes, that will do. 1/4 remove the aicv hose from the rubber intake pipe b4 the throttle body, and spray into the throttle body whilst the motor is going.
  19. https://i.imgur.com/dPd9rro.jpg...

    https://i.imgur.com/dPd9rro.jpg
    https://i.imgur.com/HITr8VI.jpg
    https://i.imgur.com/KFdX7fs.jpg
    https://i.imgur.com/mSAGz67.jpg
    https://i.imgur.com/2hCbEa2.jpg

    part numbers for all the 10an...
  20. https://i.imgur.com/yyVrk7O.jpg fitted up with...

    https://i.imgur.com/yyVrk7O.jpg

    fitted up with both defi and oem oil pressure/temp sensors
  21. pic of the oil block adapter,with the extra npt...

    pic of the oil block adapter,with the extra npt thread tapped for the oil temp sensor, and how it looked with the aeroflow AF849-10-10 & AF840-10 fittings in it.

    https://i.imgur.com/gyxDBmXl.jpg
  22. Replies
    9
    Views
    3,903

    steering locks dont work. me, hack saw, 1 min,...

    steering locks dont work. me, hack saw, 1 min, and its gone.

    alarm, kill switch, tracker. or remove the rotor plug every time you leave the car.
  23. its the same thing. mine has both bsp and npt,...

    its the same thing. mine has both bsp and npt, and i tapped another npt to replace a sandwich plate for my defi oil pressure/temp sensors
  24. quick update. been having issue's with the oil...

    quick update. been having issue's with the oil filter block developing small fractures and leaking oil everywhere. always wanted to fit an oil cooler, so i went it this direction. first is an...
  25. Thread: Upgraded Cam

    by sss4me
    Replies
    24
    Views
    5,359

    sss automotive has them, some members bring them...

    sss automotive has them, some members bring them in / export sometimes, like pten developments in nz
Results 1 to 25 of 278
Page 1 of 12 1 2 3 4