Search:

Type: Posts; User: GTI

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    4,763

    Tooth count was the same, so was the diameter....

    Tooth count was the same, so was the diameter. All fitted up and took her for a spin around the block. Runs like a dream. Finally. Almost ready to go for a roadworthy now.

    Thanks for all your help...
  2. Replies
    13
    Views
    4,763

    Ahh.. ok. How can I check if they are? Is there a...

    Ahh.. ok. How can I check if they are? Is there a difference in size I can measure, or number of teeth on the gear? Anything?
  3. Replies
    13
    Views
    4,763

    Thanks. Its what I was kind of thinking, just...

    Thanks. Its what I was kind of thinking, just wanted to hear it from someone who knows.. I've striped my stock n15 box down and swapped the gear set over into the lsd box now. From what I remember,...
  4. Replies
    13
    Views
    4,763

    So the gears look good. Selectors look good and...

    So the gears look good. Selectors look good and from what I can tell are working.

    1306

    But after having a good look I found this!!! All three bolts are loose!!! I'm guessing this is why 3rd...
  5. Replies
    3
    Views
    2,051

    Ok I've gone over the loom, can't see any...

    Ok I've gone over the loom, can't see any problems or damage anywhere else. It seems in good condition. The only thing that was messed with was the AFM wire.

    I'm stuck Cozzm0. Don't know what...
  6. Wanted Coilovers suit N15 SSS - Anywhere, I'll pay shipping., VIC 3802

    For Sale/Wanted/Wrecking wanted_parts
    Brief Description Coilovers suit N15 SSS
    Condition Good Condition, Complete.
    City/Town Anywhere, I'll pay shipping.
    State VIC
    Postcode 3802 ...
  7. Wanted Are you referring to the pipe with the 5 bolt...

    Are you referring to the pipe with the 5 bolt flange that comes directly off the turbo and has a fitting for the o2 sensor? If so I think I have a few of those.
  8. Replies
    3
    Views
    2,051

    Car has no power - ECU error code 11

    Ok so im getting error code 1-1 which I believe is Crank Angle Sensor. I tried changing the whole dizzy with a spare one and got the same error. Could it be a wiring issue?

    The car runs, but wont...
  9. Replies
    13
    Views
    4,763

    Thanks Cozzm0, it worked perfectly. Every gear is...

    Thanks Cozzm0, it worked perfectly. Every gear is perfect, except third. I have no third gear! So it seems the spare gearbox I had wasn't in working order. Although when I opened up the box to have a...
  10. Replies
    13
    Views
    4,763

    Yes its adjusted all the way and there is still...

    Yes its adjusted all the way and there is still slack in the cable. Selecting gears is not smooth, I have to use force.
  11. Replies
    13
    Views
    4,763

    Gear change / clutch issues??

    Ok so I have new pressure plate, new clutch, new PAR flywheel, VLSD gearbox.

    The clutch cable is adjusted all the way and wont go any further. Is there something I'm missing or do I need a new...
  12. Replies
    7
    Views
    2,523

    Cheers for the diagrams, all good now. Car revs...

    Cheers for the diagrams, all good now. Car revs lovely now. Just need to sort out my idle, not working well when cold. But smooth when warm.
  13. Replies
    7
    Views
    2,523

    So much for buying a second hand loom in "good...

    So much for buying a second hand loom in "good condition". Bloody gumtree... The thing is a mess, absolute dumb ass wiring job! The AFM wire has been cut before or replaced and its not soldered or...
  14. Replies
    7
    Views
    2,523

    Error code 12 - AFM circuit open or shorted. ...

    Error code 12 - AFM circuit open or shorted.

    Cozzm0 do you know what the afm wiring should be like so i can check the voltages and the ground?
  15. Replies
    7
    Views
    2,523

    Car wont rev, wont idle and is fouling plugs..

    Ok so finally got a spare stock motor in while the other one is built, but the pos won't run.

    Can't rev past about 2500-3000, it just stutters and cuts out. Feels like ECU is in safe mode. I got...
  16. Replies
    16
    Views
    6,234

    Cheers for the advice about the springs Leroy....

    Cheers for the advice about the springs Leroy. Can I ask what cams you were using?

    As for the motor, I am actually running a 54C motor, not a 53J. It will be N/A, but its still a complete GTiR...
  17. Replies
    16
    Views
    6,234

    Ok Im looking at Supertech, their springs listing...

    Ok Im looking at Supertech, their springs listing says max lift 17mm, but their complete kit with springs and retainers says max lift 10.6mm?? wtf?? Do you know any local companies that sell quality...
  18. Replies
    0
    Views
    1,755

    Any one have a stock N15 exhaust?

    Does anyone in Melbourne have a stock n15 exhaust I can buy for cheap or borrow for a day? Need to re-register my car..
  19. Replies
    16
    Views
    6,234

    Haha my wallet isn't lacking in size, I'm just...

    Haha my wallet isn't lacking in size, I'm just trying to keep from thinning it out :D But I've lost that battle today. I was told off, flamed and laughed at by a few close friends, so I've decided...
  20. Replies
    16
    Views
    6,234

    70mm on a DE would be an upgrade, but I don't...

    70mm on a DE would be an upgrade, but I don't think you've got that right when looking at the GTiR head.

    The 4 stock throttles are 45mm each. That's an area of 1590 each * 4 = 6360 total surface...
  21. Replies
    16
    Views
    6,234

    That's actually a brilliant idea thanks! Never...

    That's actually a brilliant idea thanks! Never thought of just removing the throttles and adding 1 large one, but would need to go bigger than 90mm to have any affect. The stock gtir are 45mm, so...
  22. Replies
    16
    Views
    6,234

    No I doubt I'll get anywhere near that figure,...

    No I doubt I'll get anywhere near that figure, especially with stock cams. Besides, US dyno's read higher. So realistically if I hit 180whp it would be nice. What are your thoughts? I dont know...
  23. Replies
    16
    Views
    6,234

    Not sure I understand your question? If you mean...

    Not sure I understand your question? If you mean power, I don't know as there isn't much info to go by. Only one I found was from a guy in the u.s. that made 227whp from a similar build - back in...
  24. Replies
    16
    Views
    6,234

    Advice needed - GTiR cams in N/A setup

    Hey guys, need some help with my build.

    I've been doing a bit of research regarding using the GTiR cams in an N/A motor. From what I've gathered they will be quite good and aggressive but I need...
  25. Replies
    3
    Views
    2,114

    SOLD Do you have the specs of the cams?

    Do you have the specs of the cams?
Results 1 to 25 of 34
Page 1 of 2 1 2