Search:

Type: Posts; User: Cozzm0

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    16
    Views
    9,395

    No gasket. The rubber ring is packing material...

    No gasket. The rubber ring is packing material only to stop the sharp edges ripping through the box. Silicone RTV/ Gasket goo is used on the thermostat housing to seal it. You need to clean it real...
  2. Replies
    5
    Views
    399

    A filter cannot suit N14 and N15 sr20. One is...

    A filter cannot suit N14 and N15 sr20. One is imperial thread and the other is metric so be very very careful. Is a blow engine worth saving 10 bucks on a filter. I donít think so.
  3. Replies
    16
    Views
    9,828

    Its all liquid gasket between the two halves,...

    Its all liquid gasket between the two halves, there is an o-ring under the end cap cover, but pretty much just reuse the o-ring and goo the crap out of it and you'll be fine.
  4. Replies
    13
    Views
    7,351

    I wouldn't touch the original paint if i was you,...

    I wouldn't touch the original paint if i was you, unless its in a bad state. Original paint, on an original car will be worth a lot more, but your car and you're not likely to sell so i guess do...
  5. Replies
    13
    Views
    7,351

    The only issue i have with these types of...

    The only issue i have with these types of bushings over OEM is the maintenance required to keep them lubricated. Once the lubrication 'goes' the bushes bind and because they are much harder than OEM...
  6. Replies
    1
    Views
    835

    Next time it happens try and take a note of what...

    Next time it happens try and take a note of what you're doing at the time, what accessories are on, the conditions (hot,cold etc)
  7. Replies
    21
    Views
    8,396

    I used the factory RNN14 hardline, but many have...

    I used the factory RNN14 hardline, but many have used a flex hose, required just over 1M depending on how you route it and if you go direct to the slave or use the stock rubber hose on the slave.
  8. Replies
    61
    Views
    32,274

    Progress?

    Progress?
  9. Replies
    61
    Views
    32,274

    I have pulled a bushing from and N16 setup I have...

    I have pulled a bushing from and N16 setup I have here and the 300ZX bushes didn’t fit. So I’ll have to get an N15 linkage and compare it but I suspect the N15/16 is going to be the same size.
  10. Replies
    61
    Views
    32,274

    Found my 300ZX ones. Main difference I can see...

    Found my 300ZX ones.
    Main difference I can see is the step before the lip and it doesn’t have the angled edge but I don’t think that really matters for fitment.

    If you can take some accurate...
  11. Replies
    61
    Views
    32,274

    His price is just stupid, but the measurements...

    His price is just stupid, but the measurements previous in this thread aren't accurate enough to make a bushing. I have a 3D printer now days so if i get some accurate measurements i'd be able to...
  12. Replies
    61
    Views
    32,274

    #20 is a bush, #21 is a crush tube not a bushing...

    #20 is a bush, #21 is a crush tube not a bushing as such

    34557-0M000-BUSH-CONTROL ROD SUPPORT
    34556-0M000-TUBE-CONTROL ROD SUPPORT
  13. Replies
    61
    Views
    32,274

    I have the bushes but no car to try them on. ...

    I have the bushes but no car to try them on.

    Guy selling a set of original discontinued ones for $50 on Facebook

    EDIt: just spent 45 mins trying to find the bushes to no avail. I had planned...
  14. Replies
    21
    Views
    8,396

    Yeh just swap the speedo sensor over and that’s...

    Yeh just swap the speedo sensor over and that’s all.

    It will never be what it once was despite the guy having the data at he won’t ever give it up.
  15. Replies
    21
    Views
    8,396

    GTI-R slave is useless, you need an N16 slave for...

    GTI-R slave is useless, you need an N16 slave for this along with the ~10mm spacer plate that goes between the gearbox and the slave cylinder.

    I used RNN14 master and pedal personally.

    The...
  16. Replies
    21
    Views
    8,396

    Is there any particular part that you’re having...

    Is there any particular part that you’re having trouble with ?
  17. Replies
    11
    Views
    7,178

    Jack the car up and look for paint cracking on...

    Jack the car up and look for paint cracking on the black painted metal suspension components.
  18. Replies
    2
    Views
    7,878

    Never gonna sell it are you ?

    Never gonna sell it are you ?
  19. Replies
    4
    Views
    7,207

    Case halves are gasket goo / silicone rtv only....

    Case halves are gasket goo / silicone rtv only. Run a thin bead around the lip on the inner edge of each of the bolt holes to seal it. Don’t use too much and give it 24 hours to cure before you put...
  20. Replies
    2
    Views
    6,038

    Anything that is cracked really. I only replace...

    Anything that is cracked really. I only replace when there is visible issues otherwise you'd be refreshing them way too often. Nothing beats OEM quality either, no matter what the aftermarket says...
  21. Replies
    1
    Views
    2,103

    Its not a linear difference.

    Its not a linear difference.
  22. Replies
    20
    Views
    9,527

    Fuel pumps need to be tested under pressure. Its...

    Fuel pumps need to be tested under pressure. Its pretty pointless pumping into a jar. All that will confirm is if its totally rat **** if it can't pump some fuel with no pressure on it.
  23. Replies
    20
    Views
    9,527

    yeh that's the messy messy messy way to do it.

    yeh that's the messy messy messy way to do it.
  24. Replies
    1
    Views
    2,700

    1. 10mm long socket under the hand brake lever in...

    1. 10mm long socket under the hand brake lever in the car.
    2. you need to twist them back into place. use the right tool or a set of needle nose pliers. makes sure you run a flat blade non-sharp...
  25. Replies
    20
    Views
    9,527

    Make sure your plug is orientated correctly...

    Make sure your plug is orientated correctly according to the video.

    what happens when your friends scan tool is connected? it can't connect? maybe there is a wiring issue or the connection inside...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4