Search:

Search: Search took 1.00 seconds.

  1. Replies
    2
    Views
    10,323

    I have had the Hurricane headers for 18 years on...

    I have had the Hurricane headers for 18 years on the Red Jett.

    I can recommend them. Wrap them in 'header wrap' as I have done, see pic.

    1779

    A bit on header wrap:
    ...
  2. Replies
    21
    Views
    42,579

    Cursed

    Cursed
  3. Replies
    3
    Views
    4,668

    Bump.

    Bump.
  4. Replies
    3
    Views
    7,079

    Also another question is, I have an n14 and want...

    Also another question is, I have an n14 and want to put a32 maxima rears on however for n15s I know they are bolt on but n14 I imagine the same except the rotor heights are different. Would they fit...
  5. Replies
    3
    Views
    7,079

    basically you need your choice of caliper,...

    basically you need your choice of caliper, matching rotors milled down a TOTAL of 8mm off the diameter, then redrilled to 4x100, same as the studs will need to be. n16 hubs to fit the calipers too...
  6. Replies
    3
    Views
    7,079

    Anyone? Cheers

    Anyone? Cheers
  7. Replies
    20
    Views
    16,470

    Hmmm . . . I replaced my fuel pump (under back...

    Hmmm . . . I replaced my fuel pump (under back seat) at 100,000 klicks.

    The fuel strainer was filthy.

    Incidentally, when I had the Red Jett dyno-tuned at ChipTorque, Gold Coast, Lachlan Ridell...
  8. Replies
    20
    Views
    16,470

    It's been about 15,000k's max since I replaced...

    It's been about 15,000k's max since I replaced the fuel filter. Was either last service or the one before, can't quite remember but it has definitely been done recently
  9. Replies
    20
    Views
    16,470

    One last suggestion. The FUEL FILTER could be...

    One last suggestion.

    The FUEL FILTER could be clogged.

    How long since last changed.
  10. Replies
    20
    Views
    16,470

    That's something that's definitely on the list to...

    That's something that's definitely on the list to do as well. I have done it before (with the same stuff) but it can't hurt to put another can or two through.

    As for the k's, it's just gone over...
  11. Replies
    20
    Views
    16,470

    This may be a long-shot, but maybe there is crud...

    This may be a long-shot, but maybe there is crud and sludge in your intake and valves, etc.

    How many klicks on the odo?

    Try two cans of this stuff.
    ...
  12. Replies
    20
    Views
    16,470

    It's definitely as per the video, with the...

    It's definitely as per the video, with the 'square edge' of the plug facing to the right.

    Yeah that's exactly what was happening. When it was connected it was saying 'could not connect'. I'm not...
  13. Replies
    20
    Views
    16,470

    Make sure your plug is orientated correctly...

    Make sure your plug is orientated correctly according to the video.

    what happens when your friends scan tool is connected? it can't connect? maybe there is a wiring issue or the connection inside...
  14. Replies
    20
    Views
    16,470

    Hey mate, I watched that video the other day,...

    Hey mate, I watched that video the other day, that's the procedure I have been attempting to do to no avail. I switch the key to the on position, the check engine light comes on and stays on, I...
  15. Replies
    20
    Views
    16,470

    Does this help? ...

    Does this help?

    https://www.youtube.com/watch?v=kYpSLkMSgRc

    Cheers.
  16. Replies
    20
    Views
    16,470

    Issue with checking fault codes

    I'm wondering whether someone has experienced the same issue I have and can provide some advice on how to sort it out. I have a series 2 N15 sedan (GA16), and I'm trying to retrieve the fault codes...
  17. Replies
    21
    Views
    42,579

    $h!tbox

    $h!tbox
  18. Replies
    21
    Views
    42,579

    Unpredictable

    Unpredictable
  19. Yay, thanks guys, love your work! getting sick...

    Yay, thanks guys, love your work!

    getting sick of the crap that happening on facebook lately and glad to be here.

    ummm, vendors section? is it coming back?
  20. Oh geez that's a name I haven't heard in a long....

    Oh geez that's a name I haven't heard in a long. You guys are really coming out of the woodwork!
  21. Yo yo, I own a sss. Found this place hope to...

    Yo yo,

    I own a sss. Found this place hope to learn n have a great time here.


    SSS _Hoon
Results 1 to 21 of 21