Search:

Page 1 of 2 1 2

Search: Search took 1.00 seconds.

  1. There's a Nismo Sedan concept for you homos ...

    There's a Nismo Sedan concept for you homos

    http://s3.caradvice.com.au/thumb/3000/1500/wp-content/uploads/2013/11/Pulsar-Nismo-19.jpg
  2. ECU Talk Firmware update allows BASE IDLE / TIMING SET !

    Greetings Lads and Lassies !

    I've been working with Peter, the creator of The ECUTalk Consult LCD V2 to add a much needed feature to make his product even better. BASE IDLE / TIMING ADJUST MODE...
  3. pga facebook,pog facebook, taarks, coastmodz,pten...

    pga facebook,pog facebook, taarks, coastmodz,pten developments.
  4. Replies
    10
    Views
    1,221

    Ive attached the clutch cable adjustment extract...

    Ive attached the clutch cable adjustment extract from the service manual for anyone who experiences the same issue in the future and stumbles across this thread.

    1516
  5. Replies
    10
    Views
    1,221

    1515 The above photo is what the culprit was....

    1515

    The above photo is what the culprit was. I looked in the service manual and found the section on clutch cable adjustment. Tighten adjustment knob until no free play, turn back to loosen...
  6. Replies
    5
    Views
    831

    Trolley jack: Front - centre of the...

    Trolley jack:

    Front - centre of the crossmember under the motor.
    Front single side - using a block of wood to spread load or padded jack, just behind the control arm on the flat area of the...
  7. Replies
    4
    Views
    738

    Its "useful" because that's what the factory...

    Its "useful" because that's what the factory gauge reads in.
  8. Replies
    6
    Views
    857

    i doubt the pulling left bit is a gearbox issue....

    i doubt the pulling left bit is a gearbox issue. more likely a cv or wheel alignment issue.

    the seals and small (rhs) bearing are easy enough, but the big bearing is hard to get if it needs...
  9. Replies
    17
    Views
    3,007

    I have done this, - underneath you glove box...

    I have done this,

    - underneath you glove box (the hinges) there are some 'L' shaped pins that hold the glove box in place.

    - the resistor is inside the WHITE container where the fan is located...
  10. That's a great write up thanks mate Sent...

    That's a great write up thanks mate


    Sent from my iPhone using Tapatalk
  11. Replies
    6
    Views
    1,256

    SOLD Random JDM N15 VZ-R Parts - Hornsby, NSW 2077

    For Sale/Wanted/Wrecking for_sale_parts
    Brief Description Random JDM N15 VZ-R Parts
    Condition Good, Great and Fair
    City/Town Hornsby
    State NSW
    Postcode 2077
    Contact Details PM...
  12. Replies
    4
    Views
    1,090

    They came up good :) There are two things I use...

    They came up good :)
    There are two things I use for wheels that I always have around the house -

    Dishwashing liquid (morning fresh). It cuts through the grease and grime very well.
    WD40 to...
  13. Replies
    4
    Views
    1,090

    Anodized bronze is the worst. Those came out...

    Anodized bronze is the worst. Those came out really nice.

    Bug and tar remover gets whipped out for anything that just won't budge.
  14. Replies
    8
    Views
    1,666

    Thanks Paullus. I knew/know how, but editing the...

    Thanks Paullus. I knew/know how, but editing the unwanted parts on my phone gets a bit hard. Easier on a PC. Which I'll be back at about an hour or two from now and can ask away again.
  15. Replies
    5
    Views
    1,225

    I just put a VE in to make it easier, now i don't...

    I just put a VE in to make it easier, now i don't have any problems.
  16. Ethanolaholic I believe you now have something...

    Ethanolaholic
    I believe you now have something that belongs here :)
  17. SOLD Awesome, thanks mate

    Awesome, thanks mate
  18. I removed a 6 speed to put a 5 speed back in,...

    I removed a 6 speed to put a 5 speed back in, dumbest thing i ever did.
  19. Replies
    8
    Views
    2,585

    Sticky: You're a legend, This is why you get paid the big...

    You're a legend, This is why you get paid the big bucks Paullus
  20. only one thing? They stopped making the best...

    only one thing?

    They stopped making the best looking model pulsar The N14 Jap Spec SSS
  21. Sounds like it's down your way Leroy! You're up ;)

    Sounds like it's down your way Leroy! You're up ;)
  22. Replies
    27
    Views
    5,255

    Don't be ridiculous, if you go boosted and reach...

    Don't be ridiculous, if you go boosted and reach over the 300kw mark you'll hardly ever break anything

    1049
    1050
    1051

    You'll never melt Cp pistons, a genuine Greddy turbine wheel, break...
  23. Replies
    27
    Views
    5,255

    Really? Wow, Vlad sounds like the kind of guy I'd...

    Really? Wow, Vlad sounds like the kind of guy I'd like to be
  24. Replies
    4
    Views
    1,669

    https://fbcdn-sphotos-e-a.akamaihd.net/hphotos-ak-...

    https://fbcdn-sphotos-e-a.akamaihd.net/hphotos-ak-xtf1/v/t1.0-9/12249583_10153875074691019_606557159031414602_n.jp ...
  25. Replies
    4
    Views
    1,669

    Sydney Red Bull Billy Cart Race 2015

    Here some photos and video from today's Sydney Red Bull Billy Cart Race 2015


    https://www.youtube.com/watch?v=z-mk6xeNJLc&feature=youtu.be
    ...
Results 1 to 25 of 33
Page 1 of 2 1 2