Search:

Search: Search took 1.00 seconds.

  1. Replies
    8
    Views
    688

    ECU won't know or care about the purge solenoid...

    ECU won't know or care about the purge solenoid being gone but you do need it for the vapours from the fuel take to be safely delt with unless you block all that stuff off too (not recommended i...
  2. Replies
    2
    Views
    685

    Rear beam bending

    Checking through the depths of my hard disk for some car porn i haven't seen in a long time and i found these pictures. Thought best to post them up. I can't remember who when what where why, but...
  3. Replies
    15
    Views
    1,768

    I often buy from www.amayama.com but only works...

    I often buy from www.amayama.com but only works out worth while to buy a few things at once as shipping kills if it you don't buy other things like filters, dizzy cap & rotor etc etc. I'll usually...
  4. Replies
    15
    Views
    1,768

    The most important thing when replacing the...

    The most important thing when replacing the gasket, is to follow the service manual procedures.

    As important is to clean, clean and clean again the surfaces. This means clean the mating surface on...
  5. Replies
    4
    Views
    1,489

    For Sale Updated with exterior photos :)

    Updated with exterior photos :)
  6. Thread: Lsd gearbox

    by Cozzm0
    Replies
    5
    Views
    1,205

    Other good thing with the Torsen/Helical LSD is...

    Other good thing with the Torsen/Helical LSD is that you don't need to use a special oil for the gearbox and they never "wear out" so nothing to replace/rebuild. Plus, they're great for general...
  7. N14/N15 SR20 oil filter location.

    N14/N15 SR20 oil filter location.
  8. Replies
    17
    Views
    8,543

    a few thoughts... most engine wear occurs at...

    a few thoughts...

    most engine wear occurs at startup. a smaller lower (winter) number is only going to help you. nissans factory fill was/is 7.5w-30. most people use a 5w-.

    if you haven't got a...
  9. Replies
    17
    Views
    3,904

    All you guys, Check out the 2 articles i have...

    All you guys,
    Check out the 2 articles i have posted in this section,
    Mike Kojima talks about roll centre, roll couple, suspension geometry, bump steer, toe steer, over lowering and much more, ...
  10. Replies
    38
    Views
    9,919

    As you can see, WEIGHT TRANSFER and AVAILABLE...

    As you can see, WEIGHT TRANSFER and AVAILABLE TRACTION are the 2 things that are responsible for all this happening,

    Just so people can understand this completely,
    I want to give another...
  11. Replies
    38
    Views
    9,919

    There's something I want to explain to you all as...

    There's something I want to explain to you all as there seems to be a lot of debate about upgrading rear brakes

    What I want to make very clear to you all is that there's more to braking than just...
  12. Sticky: Why lowering your Pulsar will make it handle worse unless it's done properly

    http://www.motoiq.com/MagazineArticles/ID/2804/The-Ultimate-Guide-to-Suspension-and-Handling-Its-All-in-the-Geometry-Part-One-The-Roll-Center.aspx
  13. Replies
    10
    Views
    1,974

    Here is the space i had to work with ...

    Here is the space i had to work with

    https://scontent-lax3-1.xx.fbcdn.net/hphotos-xft1/v/t1.0-9/1913618_216143486018_1123737_n.jpg?oh=288d690d743b81cbb8bd939afe0e9a70&oe=56E899C5
  14. Replies
    38
    Views
    9,919

    Just to update this in terms of the hand brake...

    Just to update this in terms of the hand brake cable brackets themselves you need the GTiR brackets to make the GTiR calipers fit with the handbrake, I found this out the hard way and just to show...
  15. Replies
    17
    Views
    3,904

    1031 Here u go part no snf22

    1031
    Here u go part no snf22
  16. Replies
    4
    Views
    1,783

    https://fbcdn-sphotos-e-a.akamaihd.net/hphotos-ak-...

    https://fbcdn-sphotos-e-a.akamaihd.net/hphotos-ak-xtf1/v/t1.0-9/12249583_10153875074691019_606557159031414602_n.jp ...
  17. Replies
    4
    Views
    1,783

    Sydney Red Bull Billy Cart Race 2015

    Here some photos and video from today's Sydney Red Bull Billy Cart Race 2015


    https://www.youtube.com/watch?v=z-mk6xeNJLc&feature=youtu.be
    ...
  18. Replies
    38
    Views
    9,919

    I'm not sure if the maxima hubs change the offset...

    I'm not sure if the maxima hubs change the offset but using the maxima caliper bracket with gtir caliper changes the position of the caliper to suit the maxima rotor correctly.
  19. Replies
    38
    Views
    9,919

    As above, with the 278mm maxima rear rotors you...

    As above, with the 278mm maxima rear rotors you can re drill them and use GTIR calipers with maxima calipers brackets. The part numbers for the brackets are 619-503 or 14-1506. Im going to be using...
  20. Replies
    17
    Views
    3,159

    you just belt the knuckle on the hub needs a...

    you just belt the knuckle on the hub needs a solid firm hit
  21. Replies
    38
    Views
    9,919

    N14 Rear Brake Upgrade/Info

    So ive been playing with the rears on bot N14's and years ago there was a large amount of info on here. So i would like to try and build up a bit of thread

    Now few questions

    1 - Are my N14...
  22. Replies
    7
    Views
    2,395

    My pulsar challenge car

    Nice to see there is a pulsar challenge sub forum.

    heres my car I built a couple of years ago.

    finished 4th in the 2014 championship.
  23. walbro pump time. i ended up with a 342. some...

    walbro pump time. i ended up with a 342. some pictures to help you choose.

    http://i.imgur.com/UBYE8V1l.jpg

    got some 370cc injectors from brendan @ pten

    http://i.imgur.com/TZ6VhnUl.jpg
Results 1 to 23 of 23