Search:

Type: Posts; User: sss4me

Page 1 of 10 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    29

    common issue. new genuine oring for the win. mark...

    common issue. new genuine oring for the win. mark your timing before you take it out.
  2. Replies
    1
    Views
    16

    dont mix the dots. use dot 4 , completely bleed...

    dont mix the dots. use dot 4 , completely bleed the whole system,start with the caliper furthest from the master cylinder to the closest one, never run it out of fluid though, and NEVER depress the...
  3. Thread: Ecu Options

    by sss4me
    Replies
    3
    Views
    186

    nistune on a gtir ecu or n14/n15 ecu with a gtir...

    nistune on a gtir ecu or n14/n15 ecu with a gtir basemap.done.

    big shoutout to haltech if you do happen to get some cash together.
  4. Replies
    2
    Views
    136

    engineers report. stronger gearbox with a lsd....

    engineers report. stronger gearbox with a lsd. 3inch exhaust.good clutch and radiator.
  5. Nearly 5 years after it started, it has finally...

    Nearly 5 years after it started, it has finally finished. After an eternity, the new head and intake was fitted, and the new n1 exhaust cam to compliment the 184c intake. The head was properly...
  6. Replies
    10
    Views
    5,327

    heres a few close up photos from last week. they...

    heres a few close up photos from last week. they are available for both p11 and p12 heads, and feature lengths from 5 to 9 inches. made for the standard sized head, and will fit our fwd platform with...
  7. Replies
    2
    Views
    382

    also just replaced mine with a 26mm natrad one....

    also just replaced mine with a 26mm natrad one. more than enough cooling and cheap enough.
  8. Replies
    4
    Views
    392

    you'll be fine with that.

    you'll be fine with that.
  9. Thread: High idle?

    by sss4me
    Replies
    4
    Views
    446

    whilst its going,gently 1/2 pull out the hose...

    whilst its going,gently 1/2 pull out the hose that runs to the iacv (its located on the rubber intake hose , dont pull it right off, it will stall), use a long squirter attachment on your can of...
  10. Replies
    18
    Views
    1,535

    yes, i double checked, and amended ^^ hope the...

    yes, i double checked, and amended ^^
    hope the tensioner fixes it, it should
  11. Replies
    8
    Views
    912

    Wanted pga or pog facebook sites are your friend.

    pga or pog facebook sites are your friend.
  12. Replies
    18
    Views
    1,535

    sump is 3.4lts with filter. 3.2ltrs without...

    sump is 3.4lts with filter. 3.2ltrs without filter. if you put it 3.2 and its overfilled, theres issues somewhere. sumps not dinted?

    listened 20 times to this, it sounds like a metal resonance...
  13. Thread: High idle?

    by sss4me
    Replies
    4
    Views
    446

    cold idle rpm is spot on. warm is 750rpm...

    cold idle rpm is spot on.
    warm is 750rpm +/-50rpm i think.
    if you've got cams, a little more is good.
    if its not bothering you, leave it. stalling everwhere is the polar opposite problem and much...
  14. Replies
    4
    Views
    697

    same same, just upgraded part number, nissan...

    same same, just upgraded part number, nissan sometimes change the place/country that makes them, then they change the number to confuse ppl.
  15. Replies
    10
    Views
    5,327

    big news today, with the release of efi...

    big news today, with the release of efi hardware's new 52.5mm itb's for sr20ve

    https://i.imgur.com/AwLRAjQl.jpg
    https://i.imgur.com/qVxEyVul.jpg
    https://i.imgur.com/G0aTcrdl.jpg
  16. Replies
    2
    Views
    312

    you could try a very liberal spray of upper...

    you could try a very liberal spray of upper cylinder cleaner into the intake plenum b4 the throttle body, and some down the hose to the iacv valve
  17. Replies
    9
    Views
    732

    had my ebay ones in for many many years now....

    had my ebay ones in for many many years now. interestingly the oem ones were 4 figures. $60 on ebay, they will do fine. get yourself some bonnet ones while your at it
  18. Replies
    11
    Views
    6,343

    "I have just been reading some posts on a SR...

    "I have just been reading some posts on a SR forum regarding camshafts and why some aftermarket exhaust cams are made smaller than the intake..where Nissan do not do this.

    Here are a few points of...
  19. Thread: VALVE Shim kit

    by sss4me
    Replies
    2
    Views
    510

    for a ?

    for a ?
  20. Replies
    11
    Views
    6,343

    There are 2 main ways of making power, given base...

    There are 2 main ways of making power, given base identical motor specs.
    1. raise the motors volumetric efficiency.
    2. raise the motors max hp rpm point.

    There is a ton of things to do to...
  21. Replies
    6
    Views
    3,342

    better add socal raceparts in here. they started...

    better add socal raceparts in here. they started with the first tr-y's, and now are making a few other designs as well. first ones a nice tri-y megaphone model, then the conventional tri-y
    ...
  22. mazworx head hardware kit fitted last week. ...

    mazworx head hardware kit fitted last week.

    http://i.imgur.com/5Riy1nd.jpg
  23. Thread: SR20VE Swap

    by sss4me
    Replies
    3
    Views
    624

    drivers side yes, passengers side no (if its a...

    drivers side yes, passengers side no (if its a 32v)

    http://i.imgur.com/egPfNhh.jpg
  24. its only recently the forum has allowed photo's...

    its only recently the forum has allowed photo's straight from the members records,before you needed a photo publisher of some sort.

    i have full intent to replace the photo's. got a new imgur...
  25. Thread: SR20VE Swap

    by sss4me
    Replies
    3
    Views
    624

    you will need to swap both the loom and ecu over,...

    you will need to swap both the loom and ecu over, and whatever happens to switch the cams over if its not the ecu.

    the passengers side cv is different, if indeed its a 32v gearbox. the easiest...
Results 1 to 25 of 236
Page 1 of 10 1 2 3 4