Search:

Page 1 of 3 1 2 3

Search: Search took 1.00 seconds.

  1. Replies
    2
    Views
    151

    probably not enough change with a cammed de to...

    probably not enough change with a cammed de to warrant 4-1's. worth doing with the higher redline of a ve though. fuji's are a good option if the coin permits on a de.
  2. Replies
    3
    Views
    272

    basically you need your choice of caliper,...

    basically you need your choice of caliper, matching rotors milled down a TOTAL of 8mm off the diameter, then redrilled to 4x100, same as the studs will need to be. n16 hubs to fit the calipers too...
  3. Replies
    4
    Views
    368

    yes. but change your old temp sensor and dizzy...

    yes. but change your old temp sensor and dizzy into the new motor. temp sensor has a different plug. n15 dizzy has internal coil, n14 doesnt. good time to clean out the iacv as well
  4. Replies
    4
    Views
    368

    yes. you will need the old n15...

    yes. you will need the old n15 flywheel/clutch/flywheel bolts, temp sensor, dizzy,ecu, and wiring.
  5. Thread: Spark Plugs

    by sss4me
    Replies
    3
    Views
    493

    unless you got some serious mods (like 12-1+...

    unless you got some serious mods (like 12-1+ pistons), your current plug is fine.
  6. Replies
    9
    Views
    1,319

    steering locks dont work. me, hack saw, 1 min,...

    steering locks dont work. me, hack saw, 1 min, and its gone.

    alarm, kill switch, tracker. or remove the rotor plug every time you leave the car.
  7. Thread: Upgraded Cam

    by sss4me
    Replies
    24
    Views
    2,122

    sss automotive has them, some members bring them...

    sss automotive has them, some members bring them in / export sometimes, like pten developments in nz
  8. Thread: Upgraded Cam

    by sss4me
    Replies
    24
    Views
    2,122

    your overthinking it. people (like me) have...

    your overthinking it. people (like me) have buggered around on a dyno for hours trying all kinds of difference centrelines to make more power, but 9 times out of 10, with the aftermarket cams ground...
  9. Thread: Upgraded Cam

    by sss4me
    Replies
    24
    Views
    2,122

    the high lift will bring small performance gains....

    the high lift will bring small performance gains. not much. to make big performance you need more (lots more) duration. and a ve motor. the end.
  10. Thread: Upgraded Cam

    by sss4me
    Replies
    24
    Views
    2,122

    again,save the $$$ on not buying cam gears, and...

    again,save the $$$ on not buying cam gears, and buy stuff that will raise hp.

    i actually tried this on my de when i had it. made bugger all difference. if you can feel 2-3hp, your doing better...
  11. Thread: Upgraded Cam

    by sss4me
    Replies
    24
    Views
    2,122

    dont bother with cam gears. these cams run on...

    dont bother with cam gears. these cams run on factory centrelines. you most probably wont see any gain by moving them.

    with the standard de intake manifold, the power will be all over before 7k....
  12. Replies
    2
    Views
    547

    unless its the best conditioned pulsar in...

    unless its the best conditioned pulsar in australia, and you want it as a museum piece, swap the motor.
  13. Replies
    5
    Views
    854

    dba imo the best rotors. quality wise. good pads...

    dba imo the best rotors. quality wise. good pads are the most important buy though. fresh brake fluid and braided brakes lines are helpful

    i like project mu pads, but there are plenty of quality...
  14. Replies
    11
    Views
    1,892

    254013m101 now go buy the good second hand one!

    254013m101

    now go buy the good second hand one!
  15. Replies
    10
    Views
    1,415

    common issue. new genuine oring for the win. mark...

    common issue. new genuine oring for the win. mark your timing before you take it out.
  16. Replies
    2
    Views
    542

    dont mix the dots. use dot 4 , completely bleed...

    dont mix the dots. use dot 4 , completely bleed the whole system,start with the caliper furthest from the master cylinder to the closest one, never run it out of fluid though, and NEVER depress the...
  17. Nearly 5 years after it started, it has finally...

    Nearly 5 years after it started, it has finally finished. After an eternity, the new head and intake was fitted, and the new n1 exhaust cam to compliment the 184c intake. The head was properly...
  18. Replies
    10
    Views
    9,781

    heres a few close up photos from last week. they...

    heres a few close up photos from last week. they are available for both p11 and p12 heads, and feature lengths from 5 to 9 inches. made for the standard sized head, and will fit our fwd platform with...
  19. Replies
    4
    Views
    1,062

    you'll be fine with that.

    you'll be fine with that.
  20. https://i.imgflip.com/1s69lw.jpg...

    https://i.imgflip.com/1s69lw.jpgvia Imgflip Meme Generator
  21. Replies
    10
    Views
    9,781

    better add plazmaman to the list. this one's a...

    better add plazmaman to the list. this one's a vet model.
    1666 1667 1668 1669
  22. Replies
    5
    Views
    1,457

    my build thread in the tech section. nearly every...

    my build thread in the tech section. nearly every number you will ever need in there.
    ...
  23. Thread: Radio/CD player

    by sss4me
    Replies
    1
    Views
    1,726

    if its the factory cd player, just rip it out and...

    if its the factory cd player, just rip it out and run it over a few times. that will fix it. otherwise,no, its not.
  24. Replies
    1
    Views
    1,965

    pga facebook,pog facebook, taarks, coastmodz,pten...

    pga facebook,pog facebook, taarks, coastmodz,pten developments.
  25. i have not done this, but thats what a few guys...

    i have not done this, but thats what a few guys use. just make sure there clean before you start. as far as the bulbs go, so long as they glow yellow/orange, not red, you are good to go.
Results 1 to 25 of 61
Page 1 of 3 1 2 3