1x brand New crank angle sensor . Genuine Nissan for 1.8 manual 2001 pulsar .
1x front engine mount for 2001 pulsar , used for one week .
1x engine oil cap for 2001 pulsar ,Used .
1x coil...
Type: Posts; User: Australia
1x brand New crank angle sensor . Genuine Nissan for 1.8 manual 2001 pulsar .
1x front engine mount for 2001 pulsar , used for one week .
1x engine oil cap for 2001 pulsar ,Used .
1x coil...
Too late mate , problem is fixed permanently now , lol someone was kind enough to write the car off a few days ago while it was parked .
Yes when 4 different mechanics looked at the car and replaced a few things you would think they would of checked over all those places ( as I asked them to) , but anyway all good now and happy .
Cheers , took it to a genuine Nissan workshop yesterday and I will be buggered , they fixed it ,
Very happy.
Loose K frame bolt ! So yes it was flexing.
All the other mechanics missed it .
Cheers thanks Cozzm0 ,
Just another update :
Got a Mechanic to Replaced wheel bearing with New one .
And I installed a set of nolathane red sway bar link bushes today .
AND Still has the...
Cheers , what reason would they do it for ?
Is there any reason why someone would of installed the top coil plate incorrectly?
Or just a stuff up ?
White dots were applied for some reason ?
...
Update ,
So I worked out what was causing the knock on the video , so called dead spring tapping each other , the springs were professionally fitted king springs ....
But unfortunately it's...
Did you replace the 2 Sensors with new ones , or secondhand ?
Can you describe what "engine breaking down slightly" is ?
Took this vid of when I am pushing down on quarter panel hard , might be related hopefully , anyone else familiar with the noise ?
No excess play can be felt that I can tell
...
Cheers Cozzm0 ,
Took it to a franchise mechanic today....
and he found a engine mount that was torn that I thought was ok , he thought it was the cause so went with it , he showed me the...
Just a update , I am persistent .
Knock noise is getting more regular and a fraction louder ,
I can now make the noise happen with handbrake on standing still with car under load , it's a...
Cheers , I re-lubed the Brake guides and pad contact points last night also did the hi temp silicone ,
But after test drive the noise was still present , bummer .
Narrowed down the noise to low...
This is now getting annoying, if I use the handbrake to slow or stop the noise disappears,
Pads are 80% and discs have been machined 6 months ago ,
Could it be the pads moving or brake play...
Contact your local dealership , anyone redeemed the offer ?
https://www.productsafety.gov.au/news/takata-airbag-recalls-affecting-australian-consumers
...
Cheers , Just a update , cv boot has been done but they could not find any other issues , go figure....
Noise still present ,
Now it's more prominent upon breaking and acceleration, has almost new brake pads and machined disc rotors , have not had a car that's done it before .
Thanks , it's a N16 - it's booked in to get a cv boot done so they will have a look at it and I will get them to do the left bearing also just in case , cheers guys
Yep I've tried the full lock turning and it does not make the noise . Only happens when not turning .
Cheers Thankyou , I moved the shaft and has a little play horizontally on both Sides , not sure if it suppose to ?
https://vimeo.com/181349612
Gday , I get occasional noise when driving , like a single crack/ping noise , is the cv joint bad ?
Excessive play ?
Car is in gear and jacked up for video
https://vimeo.com/181349493
Cheers , got one on the way , with a child in the car it's a concern , where the filter goes was a little dusty [emoji51]
Went to check the N16 cabin filter behind glovebox as I've had car for approx 5 years and bingo it was missing ? Not a thing ,
All that crap not getting filtered ...
Totally agree , just went through the same thing myself , 17inch low profile to stock 15inch Nissan mags , the difference is dramatically smoother ride