Search:

Search: Search took 1.00 seconds.

  1. Replies
    4
    Views
    70,535

    32mm for the driveshaft, 22mm for the nut that...

    32mm for the driveshaft, 22mm for the nut that holds the hub into the lower control arm.
  2. Replies
    4
    Views
    70,535

    Are you talking about where the hub connects to...

    Are you talking about where the hub connects to the ball joint on the lower control arm, or the nut on the end of the driveshaft? If it's the former then it's just the 22mm nut and the split pin. If...
  3. Thread: Manual for N15

    by Paullus
    Replies
    7
    Views
    47,884

    I'd happy host it here on the forum but I think...

    I'd happy host it here on the forum but I think we'd be infringing some sort of copyright (even though everyone does it and the car is that old that Nissan wouldn't care).
  4. Replies
    16
    Views
    43,739

    I doubt it's coming from the join. My money is on...

    I doubt it's coming from the join. My money is on of the seals: driveshaft, inputshaft, selector rod.
  5. Check that the latch ring at the bottom is tight...

    Check that the latch ring at the bottom is tight in it's mounting plate. I've seen one wear loose and cause rattles.

    1418
    (not actual n14 latch catch, but example of the part I'm referring to...
  6. Starting off with a GA base isn't ideal but still...

    Starting off with a GA base isn't ideal but still workable. I've rattled off a few things that will be needed/items to consider with either route.

    Turboing your existing engine (GA16DE+T):
    -...
  7. Replies
    3
    Views
    42,283

    I forgot that I documented a bit of this in the...

    I forgot that I documented a bit of this in the Reference Section: http://pulsar.org.au/forums/content.php?160-Bushes-Related-Parts
  8. Replies
    13
    Views
    6,543

    Those 3 bolts *shouldn't* stop it engaging, as...

    Those 3 bolts *shouldn't* stop it engaging, as the shaft is supported at each end and doesn't allow for much lateral movement. Then again it might just be enough. Those bolts should have loctite or...
  9. Replies
    17
    Views
    19,494

    Link:...

    Link: http://pulsar.org.au/forums/showthread.php?177-Pollen-Filter-Upgrade-for-N15-s-Genuine-Nissan-Parts
  10. Replies
    4
    Views
    2,930

    I'd say it's ok because the flywheel is located...

    I'd say it's ok because the flywheel is located on the crank by the centre hole. I'd do the bolts up until they start to bite and give the wheel a clockwise twist/bash so the bolts are hard up...
  11. Replies
    3
    Views
    2,901

    No. The only problem I can think of is the CV...

    No. The only problem I can think of is the CV stub/drive shaft might poke out a bit far preventing the centre cap to be fitted. I can't run centre caps on some of my wheels for this reason.
  12. Replies
    8
    Views
    5,885

    To quote a post just tap the arrow in the bottom...

    To quote a post just tap the arrow in the bottom right corner like I just did. You can also edit the quote post too.
  13. Replies
    8
    Views
    5,885

    1. According to this...

    1. According to this thread there's a yellow headed bolt under the dizzy. SR20DEs are conveniently located on the thermostat housing at the front of the engine.

    2. Perfectly normal. That's the...
  14. Replies
    4
    Views
    5,086

    For Sale Because maybe the new owner (or the owner after...

    Because maybe the new owner (or the owner after that) might be on here and wants some history on the car? I did it a couple of times on the old forum. That's one of the purposes of a forum over...
  15. Yes. Post deleted. Please don't spam threads.

    Yes. Post deleted. Please don't spam threads.
  16. Replies
    8
    Views
    157,380

    Sticky: @username should do it, but probably won't work...

    @username should do it, but probably won't work on tapatalk
  17. Replies
    10
    Views
    11,008

    http://pulsar.org.au/forums/showthread.php?63-SR20...

    http://pulsar.org.au/forums/showthread.php?63-SR20DE-to-GTi-R-SR20DET-Conversion

    http://pulsar.org.au/forums/showthread.php?60-SR20DE-%28N14%29-to-SR20DET-%28U12%29-Engine-Conversion
  18. Replies
    41
    Views
    82,060

    It's in Engine & Gearbox Specific

    It's in Engine & Gearbox Specific
  19. Replies
    27
    Views
    87,434

    I didn't know Omega ran an 11 yet. He's had the...

    I didn't know Omega ran an 11 yet. He's had the plates for a while and when we last spoke he hadn't run one (but neither had I at the time!).

    Plus there's me that ran 11.9@125.

    Who is bread?...
  20. Thread: I like turtles

    by Paullus
    Replies
    6
    Views
    7,044

    https://www.youtube.com/watch?v=L8_077J5Rvw

    https://www.youtube.com/watch?v=L8_077J5Rvw
  21. Replies
    41
    Views
    82,060

    We're still figuring out exactly what perks a VIP...

    We're still figuring out exactly what perks a VIP member gets and how long that lasts, but in the meantime you can use the Contribute button at the top of the page to make a donation and be upgraded...
  22. Replies
    41
    Views
    82,060

    Can you provide more information please? Does it...

    Can you provide more information please? Does it just have a link to the attachment?

    EDIT: Don't worry I found a thread where it's happening....
  23. Oh geez that's a name I haven't heard in a long....

    Oh geez that's a name I haven't heard in a long. You guys are really coming out of the woodwork!
  24. http://metropolisarena.com/wp-content/uploads/awww...

    http://metropolisarena.com/wp-content/uploads/awww-yeah.jpg
  25. Replies
    41
    Views
    82,060

    Report all bugs/problems/suggestions here!

    As this forum is brand spankin' new, we're still working through all the bugs and mods and can't be everywhere at once to test features.

    If you encounter an error, problem, or have a suggestion on...
Results 1 to 25 of 25